Diode-led RGBW LED Tape Light Manual de usuario descargar pdf

1.877.817.6028

www.DiodeLED.com

[email protected] www.DiodeLED.com

INSTALLATION GUIDE

1 OF 4

DAZZLE 24

™

24V RGBW LED TAPE LIGHT

Do not bend LED strip light on a

horizontal plane.

Do not fold or crease LED strip light.Do not bend LED strip light to a diameter

less than 1.5 inches.

Do not put excessive pressure on surface of

strip light (e.g. glass/acrylic panes etc.).

1.5 in.

Do not cover strip light with any materials. Do not power strip light while

aached to spool or ghtly coiled.

• Install in accordance with the Naonal Electric Code and local

regulaons.

• This product is intended to be installed and serviced by a qualied,

licensed electrician.

• DO NOT connect tape directly to 120VAC power.

• To meet the tape ETL Lisng cercaon, tape light must be powered

with a compable Class 2 DC constant voltage LED driver (power

supply).

• Each LED driver is unique and may require a proper load derang,

which is dependent to the installed ambient temperature environment.

Refer to each driver specicaon sheet for full power rangs & load

derangs.

• Do not power tape light while aached to plasc spool or ghtly coiled.

Excess heat may melt the spool and/or cause damage to the tape.

• Do not install tape light in direct sunlight.

• Ensure applicable wire is installed between driver, xture, and any

controls in between. When choosing wire, factor in voltage drop,

amperage rang, and type (in-wall rated, wet locaon rated, etc.).

Inadequate wire installaon could overheat wires, and cause a re.

• Tape light, aached wire leads, and addional extension cables,

connectors, etc., are not rated for in-wall installaon unless otherwise

noted. Connectors have a Class 2 amp limit unless otherwise noted.

• Tape light must be handled with care. Excessive handling, bending, and

pressure may damage the product, voiding the warranty.

• Each tape light has a dierent power consumpon rang and maximum

run length that must be individually wired to a compable low voltage

(PWM) control or DMX decoder. Refer to the tape light packaging label

or specicaon sheet for further technical informaon.

Safety & Warnings

Tape Light Handling

DO NOT CONNECT

TO HIGH VOLTAGE

Dry Location Only

Dimmable

24V

Color Changing

Quick Specs

Included Model(s) DI-24V-RGBW-0020

Ambient Temperature † -4° ~ 122°F (-20° ~ 50°C)

Environment Indoor / dry locaon

Input Voltage 24VDC constant voltage

Power Consumpon

4.39W / 180mA per foot

For full specicaons, see the ‘Specicaon Sheet’ available at the online

product page.

†

Do not install product in an environment outside the listed ambient

temperature. Ensure adequate airow and heatsinking is considered

when mounng/installing.

DO NOT CONNECT DIRECTLY TO HIGH VOLTAGE POWER!

Read all warnings and installaon instrucons thoroughly.

WARNING

IG082514-1.3

1 2 3 4

1.877.817.6028 1
QUESTIONS? 4

Indice de contenidos

Pagina 1 - 1.877.817.6028

[email protected] www.DiodeLED.comINSTALLATION GUIDE1 OF 4DAZZLE 24™ 24V RGBW LED TAPE LIGHT®Do not bend LED strip ligh

Pagina 2

[email protected] www.DiodeLED.comINSTALLATION GUIDE2 OF 4DAZZLE 24™ 24V RGBW LED TAPE LIGHT®A. Cut the tape at the lin

Pagina 3

[email protected] www.DiodeLED.comINSTALLATION GUIDE3 OF 4DAZZLE 24™ 24V RGBW LED TAPE LIGHT®+−+−+−+−+−+−Prior to troub

Pagina 4 - QUESTIONS?

[email protected] www.DiodeLED.comINSTALLATION GUIDE4 OF 4DAZZLE 24™ 24V RGBW LED TAPE LIGHT®The following diagram is p

Comentarios a estos manuales

Sin comentarios

Diode-led RGBW LED Tape Light Manual de usuario

Busca en linea o descarga Manual de usuario para Encendiendo Diode-led RGBW LED Tape Light. Diode LED RGBW LED Tape Light User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Encendiendo Diode-led RGBW LED Tape Light