Diode-led RGB Zone Control Manual de usuario descargar pdf

1.877.817.6028

www.DiodeLED.com

[email protected] www.DiodeLED.com

INSTALLATION GUIDE

1 OF 4

RGB ZONE COLOR CONTROLLER

• Install in accordance with the Naonal Electric Code, and local

regulaons.

• This product is intended to be installed and serviced by a qualied,

licensed electrician.

• DO NOT connect directly to high voltage power. Install with a compable

Class 2 constant voltage LED driver (power supply).

• Only install compable LED drivers and xtures. Contact technical

support or visit the product page for compable products.

• This product is rated for indoor installaon and is not protected against

moisture.

• Proper heat dissipaon will prolong the working lifespan of this product.

Install in a well-venlated area free from explosive gases and vapors.

• Ensure applicable wire is installed between driver, xture, and any

controls in between. When choosing wire, factor in voltage drop,

amperage rang, and type (in-wall rated, wet locaon rated, etc.).

Inadequate wire installaon could overhead wires, and cause a re.

• Do not modify or disassemble this product beyond instrucons or the

warranty will be void.

Safety & Warnings

Prior to installaon, verify all components are a compable system. Congure and pre-test your LED system prior to permanent installaon to ensure all

components are operang correctly. Install in accordance with the NEC and local regulaons.

Installation

Quick Specs

Input / Output Voltage 5-24VDC constant voltage

Max Current Load 5A x 4CH Max 20A

Max Output Power

100W/240W/480W (5V/12V/24V)

Ambient Temperature

-22° ~ 131°F (-30° ~ 55°C)

Environment Indoor / dry locaon

Input Voltage 5VDC Built-in Lithium Baery

Transming Distance 90 .

Control Type

Pulse Width Modulaon (PWM)

3-channel RGB xtures

Ambient Temperature † -4° ~ 131°F (-20° ~ 55°C)

Turn OFF High Voltage AC Power at the main breaker. Determine Locaons to Install 3 Main Components.

Refer to the ‘System Diagrams.’

OFFOFFOFF

ONON

OFFOFF

ONON

V+

V-

V+

1) Driver 2) RGB Color

Controller

3) Fixture

Ensure applicable wire is installed between driver, xture, and any

controls in between. When choosing wire, factor in voltage drop,

amperage rang, and type (in-wall rated, wet locaon rated, etc.).

DO NOT CONNECT DIRECTLY TO HIGH VOLTAGE POWER!

Read all warnings and installaon instrucons thoroughly.

WARNING

Shock Hazard. May result in serious injury or death.

DO NOT CONNECT

TO HIGH VOLTAGE

Dry Location Only

12V

24V

RGB Zone Remote RGB Zone Receiver

For full specicaons, see the ‘Specicaon Sheet’ available at the online

product page.

†

Do not install product in an environment outside the listed ambient

temperature. Ensure adequate airow and heatsinking is considered

when mounng/installing.

DC+

DC-

V+

DO NOT PAIR MULTIPLE

REMOTES TO A SINGLE RECEIVER.

Zone 1Zone 1

DC+

DC-

V+

DC+

DC-

V+

DO NOT SET MULTIPLE

RECEIVERS TO THE SAME ZONE.

IG060914-1.2

# DI-1700

# DI-1701

1 2 3 4

1.877.817.6028 1
QUESTIONS? 4

Indice de contenidos

Pagina 1 - 1.877.817.6028

[email protected] www.DiodeLED.comINSTALLATION GUIDE1 OF 4RGB ZONE COLOR CONTROLLER®• Install in accordance with t

Pagina 2

[email protected] www.DiodeLED.comINSTALLATION GUIDE2 OF 4RGB ZONE COLOR CONTROLLER®OperationMount RGB Receiver to Surf

Pagina 3

[email protected] www.DiodeLED.comINSTALLATION GUIDE3 OF 4RGB ZONE COLOR CONTROLLER®Mode Description Chart Wiring Conne

Pagina 4 - QUESTIONS?

[email protected] www.DiodeLED.comINSTALLATION GUIDE4 OF 4RGB ZONE COLOR CONTROLLER®Additional ResourcesQUESTIONS?Visit

Comentarios a estos manuales

Sin comentarios

Diode-led RGB Zone Control Manual de usuario

Busca en linea o descarga Manual de usuario para Encendiendo Diode-led RGB Zone Control. Diode LED RGB Zone Control User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Encendiendo Diode-led RGB Zone Control